Distributed Mode Loudspeakers

My journey into home stereo speakers and high quality audio continues…

This is not a broadcast related post, but I find this type of thing interesting nonetheless. A few years ago, I began fiddling around with flat panel speakers or Distributed Mode Loudspeakers (DML). My first attempt was lackluster, although adequate and not very expensive.

I enjoy listening to all types of music. I notice that some music reproduces better than others. Piano is a particularly difficult instrument to record and faithfully reproduce because of the complexity of the instrument itself. It is a percussive string instrument. When one of the hammers strikes a sting, the string itself does not make a very loud noise. The string is connected to a sound board through a bridge. The much larger soundboard vibrates and amplifies the initial sound. Thus, the wood itself imparts a noticeable quality to the sound. Several other instruments such as acoustic guitar, violin, etc also use tonewood to amplify sound. Thus, when listening to a piano being played back on a set of speakers, it lacks much of the original texture of the actual instrument. It sounds like a recording of a piano, not an actual piano.

This made me think of ways to improve that reproduction.

A DML uses a large flat surface to reproduce sound. The large surface area and the bi-directional nature of the panel means the sound will be defuse and not directional as is the case with conventional speakers at higher frequencies.

The principle characteristics of material used in a DML is stiffness and density. The less dense (light weight) and the stiffer the better. All materials have internal resonances, some decay quickly and others, such as steel will ring for a long time. A ringing reverb sound would be undesirable in most cases. Tonewood has suitable stiffness, a relatively high sound radiation coefficient, varies in density according to species and generally dampens high frequency harmonics. Pianos often use Sitka Spruce for sound boards.

I made two terminated transmission line speakers last summer. Those sound great, but using one driver to reproduce all sound from 20-20,000 Hz has a drawback; the high end lacks detail and is very directional.

A bit of research shows that Poplar has good to very good tonewood qualities while being inexpensive and readily available at the local big box hardware store. Thus, I purchased several 1/4 x 6 x 48 inch (6 x 152 x 1220 mm) planks and a few pieces for bracing to make two 33 x 22 inch (838 x 559 mm) flat panels. The idea here is to gently cross over the transmission line speakers at 4,500 Hz with these flat panels.

The assembly process was pretty easy. It took perhaps two hours to cut all the pieces to the right size. I used a router to chamfer the edges of the back bracing, mostly to reduce the weight of the brace. Everything was glued up and allowed to dry for 24 hours.

Gluing the parts together
Back bracing

The bracing is designed to keep the panel stiff and helps with structural integrity. I sanded the fronts and backs of the panels, then finished them with Tung Oil.

Dayton tactile exciters

Each panel uses two Dayton DAEX32QMB-4 tactile exciter wired in series. There is also a Zobel network which is important for a tube amp. Most driver’s impedance will rise as the frequency increases. This rising impedance is mostly reactance from the driver coil. For solid state amps, this is not much of a problem. However, tube amps, because of the output transformer, need a fairly constant impedance across there output range. This is because the output transformer is a ratio device. The primary impedance is derived from the impedance on the secondary (e.g. what the secondary is terminated with). For example, a certain tube has a 5,000 ohm plate impedance. The output transformer is chosen to match this design specification. The output transformer is designed to drive an 8 ohm loudspeaker. However, the driver impedance rises to 16 ohms at 15 KHz and 24 Ohms at 20 KHz. Under those conditions, the tube would be seeing a 10,000 ohm impedance at 15 KHz and a 15,000 Ohm impedance at 20 KHz. This will lead to added distortion. The Zobel network keeps the impedance fairly uniform across the entire audio range.

Rather than build a cross over into the transmission line speakers, I made an external unit. This allows the speaker system components to operate independently if needed. I can easily change the cross over components for a different crossover point. I can also mix and match things in the future. In other words, it gives me a great deal of flexibility for future projects and experimentation.

Crossover and HF attenuator
Crossover and attenuator components

I made these small boxes to match the speakers. These contain the crossover and HF attenuator. The attenuator is necessary because the difference in efficiency between the transmission line driver and the tactile drivers on the DML.

The schematic looks like this:

Cross over diagram

I kept things as simple as possible. Yes, I could have made a 12 dB per octave crossover with a few additional components, however, I like the gentle blend of both drivers in the mid ranges.

A basic sweep with Room EQ Wizard shows a fairly flat response. There is a room resonance around 90 Hz which I intend to correct with some sound deadening materials in the corners and possibly a bass trap.

Room EQ Wizard waterfall display

This shows that the speaker system is relatively flat from about 200 Hz to 10 KHz. Those bumps and dips from 88 to 250 Hz are all room due to room resonance.

Room EQ Wizard SPL graph

How does it sound? Pretty good! Here is some copyright free music, recorded from youtube, then re-uploaded to youtube! It is not the best video, there is some background noise, etc. However, it give a pretty good idea of how these sound.

5 thoughts on “Distributed Mode Loudspeakers”

  1. Very cool
    Even via a YouTube video it sounds fantastic.
    Don’t let a client see this – they’ll be asking to hand make studio monitors haha

  2. Paul, what determines how far from the wall the units are hung?

    I had never heard of DML before now. It looks like fascinating stuff.

  3. Brian, thank you! If a client wants these, I will charge extra!

    Gregg, wall spacing is an on going experiment. Right now, they are about 7 inches from the wall. I have tried putting up towels behind them to deaden the back wave, but that makes it sound slightly dull. Next, I am going to try moving them further away.

  4. Thank you, Patrick! You have good eyes; the piece of Schiit on the left is a Modi Multi-bit and the piece of Schiit on the right is a Mani for that Technics SL-1200 next to it.

Leave a Reply

Your email address will not be published. Required fields are marked *