Tower lighting transformers, isolation chokes, etc

Series excited AM towers require some way to get standard AC across the base insulator to the tower lights if tower lights are required.  While many new AM towers do not have base insulators, through the use of a folded unipole, it is still a very popular design and has several technical advantages.

There are two methods for getting 60 Hz AC from zero RF potential to an excited tower:

  1. Tower lighting choke
  2. Austin Ring transformer
LBA Group TC-300 tower lighting choke
LBA Group TC-300 tower lighting choke courtesy LBA Group, Inc

When to use it depends on the tower and the RF potential on the base of the tower. For towers that are under 140 electrical degrees (RF) and carrier power levels up to 100 KW, a lighting choke works well. They are simple and less expensive than an isolation transformer.  They can be installed inside the ATU cabinet or placed in their own weatherproof enclosure as required.  Tower lighting chokes will add series impedance to the base of the tower and needs to be compensated for by adding capacitance to the circuit.  This will become more pronounced at the lower end of the band, where, if one is not careful, RF from the tower can be coupled to the transmitter building’s AC mains, which is very undesirable.

Tower lighting chokes generally consist of three separate windings, one for the beacon, one for the side lights, and one for neutral.  Their inductance is typically in the 800-1000 µH at 1 MHz region.  They can be stacked to increase their peak voltage handling capacity:

LBA Group tower strobe light choke
LBA Group tower strobe light choke courtesy LBA Group, Inc

Peak voltage is determined by the base impedance and carrier power + modulation.  On any AM station these days, a 150% peak modulation figure should be used (125% modulation allowed by FCC rules plus a 25% safety factor).  For example, station B has a base impedance of 50Ω (typical 90° guyed tower) and a carrier power of 50 KW.  The peak modulation power will be 600 KW.  Thus, the peak voltage will be Epeak = √Ppeak x R, or Epeak = √600,000 watts x 50 ohms or 5,477 volts.   With higher base impedances, the base current goes down but the base voltage goes up.  A typical 140° tower will have a base impedance of 760Ω.  Thus the peak base voltage for a 50KW carrier power modulating at 150% will be 21,354 volts.  This is the worst case scenario, as few installations are designed that way and every tower impedance is different than the theoretical self impedances given.

For towers over 140 electrical degrees, it is better to use an isolation transformer because of the RF peak voltage/peak current conditions at the base of towers that are electrically tall.  The ring transformer design minimizes stray inductance or capacitance at the base of such towers.  Austin Insulators (previously Austin Decca) makes a variety of tower base ring isolation transformers.  These have varying input and output voltages.

Diagram of typical Austin Ring transformer
Diagram of typical Austin Ring transformer courtesy Austin Insulators, Inc

I have seen these at many locations over the years. They are rugged and add only a small bit of capacitive reactance to the base of a typical tower.  They also completely isolate the building AC mains from the tower.  For very high-power installations, Austin has the A-9600, which was designed for the Navy VLF transmitter towers where base peak RF voltages can run 200,000 volts or more:

Austin A-9600 oil filled isolation transformer
Austin A-9600 oil-filled isolation transformer courtesy Austin Insulator, Inc

Voltage drop is another consideration in tower lighting design. Long runs from the transmitter building to the tower should be on heavy gauge wire and at 230 volts if possible.  FAA Circular AC 150/5345-43F “Specification for obstruction lighting equipment” advises that the input voltages for incandescent lighting systems vary by not more than ±3%.   Additional tower lighting and painting information can be found in FAA Circular AC 70-7460-1K.

Print Friendly, PDF & Email

12 thoughts on “Tower lighting transformers, isolation chokes, etc”

  1. I quickly needed to replace my blown ‘Austin’s Isolation ring transformer’, your response is require on where to purchase.

    regards

  2. Good Day! I want to put tower light in our 290ft Grounded AM tower at 765khz frequency. with carrier power of 10kw. what transformer and wire gauge can you suggest me..thanks!

  3. @Baldimir, if you have a grounded tower, then you will not need a lighting transformer or choke. As far as the wire gauge is concerned, that is a voltage drop consideration. I believe FAA rules (US) are for not less than 2% variation in brightness, thus keeping the voltage drop a low as possible is key. Assuming the top flashing beacon is two 620 watt bulbs and the system is 120 volts, the current on the beacon portion of the circuit will be 10.3 amps. 12 gauge wire will work for this, however, 10 gauge gives an added safety margin. Side light markers can be run on 12 gauge wire also. If the system is 240 volts, then the currents will be half that given in the example and wire sized can be adjusted accordingly.

  4. Looking for a method to allow 48 VDC voltage on to an AM tower from the ground based xmtr. Any recommnedations?

  5. A tower lighting choke might work, depending on how clean the DC needs to be on the hot side of the tower.

  6. I have never taken one apart, however, they are heavy enough. I would assume that it is laminated steel plates, like other transformers.

Leave a Reply

Your email address will not be published. Required fields are marked *